Quick answer: Wrap a strip of paper or string around the base of your finger, mark where it overlaps, measure that length in millimeters, then match it to a ring size chart. Most women land between US size 6 and 9, and most men between 8 and 12. If you’re between two sizes, round up — a slightly loose ring is easier to live with than one that’s stuck.
That’s the short version. Here’s how to actually get it right, plus a full conversion chart if you’re ordering from overseas or comparing US, UK, and EU sizes.
Method 1: The String or Paper Test (Free, 2 Minutes)
This is the method most jewelers still recommend, even with sizing apps available, because it’s hard to mess up if you follow it step by step.
What you need: A strip of paper (about 1 inch wide, cut from a receipt or sticky note works fine) or a piece of non-stretchy string, plus a ruler with millimeter markings.
- Wrap it around your finger. Wrap the strip around the base of the finger you’re sizing, right where the ring would normally sit — not over the knuckle.
- Mark the overlap. Use a pen to mark the exact point where the strip meets itself. Don’t pull it tight enough to indent your skin; snug but relaxed is what you want.
- Lay it flat and measure. Uncurl the strip and measure the distance from the start to your mark in millimeters. That number is your finger’s circumference.
- Match it to the chart below. Find the closest circumference in the table and read across for your US, UK, or EU size.
A few things that throw this off: measuring right after a workout or in cold weather (fingers shrink), pulling the paper too tight, or measuring over a swollen knuckle instead of the base of the finger. If you can, measure at the end of the day when your hands are at a normal temperature, and check both hands — most people’s dominant hand runs slightly larger.

Method 2: A Physical Ring Sizer
If you want more precision, or you’re sizing a ring as a gift and can’t ask the person directly, a plastic or metal ring sizer set is worth the few dollars. These are graduated rings you slide on until you find the one that fits — no math, no paper.
Two options:
- Plastic sizer sets — cheap, easy to find, fine for one-time use.
- Metal mandrel rings — sturdier, reusable, and what most jewelers actually use in-store.
Slide the largest ring you think might fit and work your way down until it moves over your knuckle with light resistance but doesn’t spin freely on the base of your finger. That’s your size.

US, UK & EU Ring Size Conversion Chart
If you already own a ring that fits and just need to convert it — or you’re comparing sizes across countries before ordering — here’s the standard conversion based on inside diameter and circumference.
| US / Canada | Inside Diameter | Inside Circumference | UK / Australia | Europe (FR/DE) |
|---|---|---|---|---|
| 5 | 15.70 mm | 49.32 mm | J ½ | 49.3 |
| 6 | 15.70 mm | 51.87 mm | L ½ | 51.9 |
| 7 | 17.32 mm | 54.41 mm | N ½ | 54.4 |
| 8 | 18.14 mm | 56.99 mm | P ½ | 57.0 |
| 9 | 18.95 mm | 59.53 mm | R ½ | 59.5 |
| 10 | 19.76 mm | 62.08 mm | T ½ | 62.1 |
| 11 | 20.57 mm | 64.62 mm | V ½ | 64.6 |
| 12 | 21.39 mm | 67.20 mm | X ½ | 67.2 |
| 13 | 22.20 mm | 69.74 mm | Z ½ | 69.7 |
For reference: most adult women fall between US size 5 and 10; most adult men fall between US size 7 and 13. If you already own a ring, you can skip the string method entirely — just measure its inside diameter with a ruler and match it to the chart.
Comfort Fit vs. Standard Fit: Why the Same Size Can Feel Different
Here’s something the string method won’t tell you: the shape of the band’s interior changes how a given size actually feels.
A standard fit band has a flat interior, so the size chart above applies directly. A comfort-fit band has rounded, polished inner edges—it slides over the knuckle more easily and sits more comfortably against the skin, but because more metal touches your finger, it can feel up to a half-size smaller than the same number in a standard-fit band.
If you’re buying a comfort-fit ring and you measured as a 7, consider trying a 7.5. Also worth knowing: wide bands (8mm or more, common in statement and gothic-style rings) fit tighter than thin bands of the same size, since more surface area is in contact with your finger. Sizing up half a size on wide bands is standard practice. (We cover why comfort-fit geometry matters for durability too, in our breakdown of 316L stainless steel.)
Common Mistakes That Throw Off Your Measurement
- Measuring a swollen knuckle instead of the finger base. If your knuckle is noticeably bigger than the base of your finger, size for the base and expect a slightly looser fit at rest — that’s normal and better than a ring that won’t pass the knuckle at all.
- Measuring at the wrong temperature. Fingers swell in heat and humidity, and shrink in cold weather or air conditioning. Measure at room temperature, not right after a hot shower or a cold walk outside.
- Pulling the string or paper too tight. This is the single most common error, and it always makes the ring come out too small.
- Only measuring once. Measure two or three times at different times of day and take the middle value.
FAQs
Most adult women fall between US size 6 and 7, though the full typical range runs from 5 to 10.
Most adult men fall between US size 9 and 10, with a typical range from 7 to 13.
Yes — a thin strip cut from paper (not cardstock) works as well as string, as long as it doesn’t stretch when you wrap it.
Size up. A slightly loose ring can be resized down or worn with a sizing insert; a ring that’s too tight often can’t be worn at all.
Slightly, yes — tolerances of a few tenths of a millimeter are common even within the same country’s sizing standard. If you’re ordering custom or bulk from a manufacturer, ask for their calibrated mandrel specs rather than assuming every “size 7” is identical.
Sourcing Ring Sizing at Scale: A Note for Jewelry Brands
If you’re building a private-label ring line rather than buying one ring for yourself, the stakes are different—a size off by half a millimeter across a production run turns into bulk returns and refund requests, not just an inconvenience.
At Jiman Jewelry, we’ve spent 19 years manufacturing custom 316L stainless steel jewelry for e-commerce brands, streetwear labels, and boutique retailers, and sizing consistency is one of the most common issues new clients ask us to help solve. For the full technical matrix — including our manufacturing tolerances and China, Japan, and EU conversions — see our jewelry size guides and technical standards reference. A few things we recommend before your first production run:
- Specify comfort fit vs. standard fit in your tech pack. Don’t leave it implied — it changes the effective size by up to half a size.
- Request calibrated mandrel verification, not just a stated size, especially on your first order with a new factory.
- Size up on wide bands (8mm+) by default in your product listings, and say so in your size guide to cut down on returns.
- Build your own customer-facing size chart using the table above — it reduces support tickets and gives buyers confidence before they order.
Looking to develop a custom ring line with verified, consistent sizing across every unit? Contact our engineering team — we typically respond with technical feedback within 12 hours.

Christina Wu is the Marketing Manager at Jiman Jewelry, sharing expert knowledge about stainless steel jewelry trends, manufacturing, customization, and industry insights to help global brands create high-quality jewelry collections.
